Ford axle identification.

355 = 3.55:1 gear ratio, open differential (No Trak-Lok, which would appear as 3L55) 8.8 = Ring gear diameter of 8.8". 0C15 = Date of construction; 0 = 2000, C = March, 15 = Day of month. If you want to take it a step further, take a look at the vehicle info sticker on the driver's door. Under the "AXLE" section, the rear end code should be "R2".The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates which Design Engineering Office is responsible for the component. There is a fair amount of detailed information contained within the part ... The most accurate differential identification is provided by the bottom line of the tag number or axle tube stamp. Differential tags can easily be used to identify Dana and Ford differentials. The Dana 50 IFS was available as an option in pre-'87 F-250 HDs (4,600 pound HD front axle option) and was routinely fitted to SuperCab F-250 HDs. By 1987, the Dana 50IFS had replaced the Dana 44IFS in F-250HDs. A front limited slip shows up in Ford data books through at least 1985."

The axle shafts are TINY. A 7.5" Ranger axle has stronger shafts. Even with 35 spline chromoly shafts, the axles will break first. If you can't find any more numbers, look at the cover. On a 60, the bottom of the centersection closely follows the cover. A 70 uses the same cover.

Early Ford Axle Identification. This article will cover Ford axles from 1928-52 passenger cars & pickups. Keep in mind, this is for Ford cars & pickups only. Trucks and …Look at the tag on your driver door. There is a category for Axle Code. Look at that code then Google it. You likely have 3.55 if you have a 4x4 or FX4 or max towing. Otherwise 3.31 would get my vote. The 10 speed trans defaults to the 3.31 unless other criteria is met as the 3.31 is a perfect match for the 10 speed.

This page should help. Following the 17-digit VIN on your truck, select the character for each box that matches it's place in the VIN. Sample V.I.N. (Vehicle Identification Number) Typical VIN. Position Number.If you are a car enthusiast or a mechanic looking for high-quality auto parts, the Detroit Axle website is your one-stop-shop. With a wide range of products and user-friendly featu...Axles the same 2" boss, if the axles are complete assemblies the next validation is spring location and perch pins. 33-34 spring on top of axle, 35-36 spring in front of axle. The spindles and the radius rod construction next definer, 33-36 spindles are different , 32-34 same steer of lf , 35,different from 36 steer off rf, 36 has shorter snout ...Jul 29, 2008. #6. These codes are for 74-77, but I suspect they are good as far back as 72. Before power steering was an option "J" was sometimes used to denote front limited slip. Rear Axle Code. A3 4.11 2780Lb w/Trac-Lok. A5 4.11 3300Lb w/Trac-Lok.

Chest freezer reset

Identifying the rear axle in a Ford vehicle is crucial for various reasons, such as determining the appropriate gear ratio for optimal performance and ensuring …

axle identification. I think I answered my own question. I did a search over on the ford-diesel.com site and found a lot of info. I seems the tag on the axle has either a 229 or 248 and the 229 is a D50 and the 248 is a D60. I have the 248 or D60 axle. I …Identifying the rear axle in a Ford vehicle is crucial for various reasons, such as determining the appropriate gear ratio for optimal performance and ensuring …Accurate Differential Identification is the first and most important step in your differential repair, upgrade or overhaul project. The following information is provided to help you identify the differential you are working on. If in doubt, consult one of our differential experts at (800)510-0950! Professional technical support is available ...Your medical ID number is a unique set of numbers that the health insurer will give you when you enroll in one of its plans. It is useful for identifying who you are and the extent...Feb 19, 2008 ... You are correct, that is the tag numbers for a Ford 8.8" rear axle, with 3.55 gears and no limited slip or what's called an "open" differential.Personally, I would suggest the 1957/72 F100 9" as it fits. I don't know if the others will and all the others have specific R & L axle shafts, while the F100's are the same R & L. F100: 1957/67 have 11" x 1 3/4" rear brakes, 1968/72 have 11 x 2 1/4" rear brakes. diff/axle identification.The D28 can be re-geared; however, units with the 3.45 ratio, going to a lower (numerically higher) ring and pinion gear must use the appropriate housing. All Explorer are 31 spline 8.8" rear. Most all Ranger 8.8" rear axles are 28 spline and all 7.5" axles are 28 spline axles. Some late model 8.8" Ranger rear axles are 31 spline.

Originally Posted by BigBlue 94. My 99 e250 has a 24 axle code. I know it's an open 3.73 Dana 60. That follows ford code with a 2 digit numbered axle code being open and a letter /number digit code for limited slip. 1959 thru today: Two digit AXLE code. If the first digit is a letter: Limited Slip.Originally Posted by BigBlue 94. My 99 e250 has a 24 axle code. I know it's an open 3.73 Dana 60. That follows ford code with a 2 digit numbered axle code being open and a letter /number digit code for limited slip. 1959 thru today: Two digit AXLE code. If the first digit is a letter: Limited Slip.How can you identify which rear axle you have? It can be narrowed down this way:1. Rear brake drum backing plate - Finding the number etched in2. The rear ax...Ford Truck Enthusiasts Forums. Older, Classic & Antique Trucks. 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks. Rear Axle Identification. 1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks Discuss the Early Eighties Bullnose Ford Truck.Dec 13, 2023 · Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle’s size and capacity, while the ...

Identifying Your Rear Axle Flange. Ford, Chevrolet, Oldsmobile, Pontiac, they all used a different axle flange at one point or another. Being able to identify the flange you have can spare you a lot of grief when it comes time to buy parts, not to mention speeding up the process as a whole. Check out the graphic below to help you identify some ...

The axle code can typically be found on the vehicle’s door tag, which is located on the driver’s side door jamb. It may also be stamped on the axle housing itself or listed on the vehicle’s build sheet. The chart provides a handy reference for decoding the axle code once it has been located. See also Fixing Transmission & Solenoid for ...Jun 5, 2017 ... In This video I show the easiest way to find the axle ratio on a 2016 Ford F-150. Link to owners manual: ...2015 - 2020 Ford F150 - 8.8 Super vs 9.75 Rear Axle Question - After lurking around this forum for a while, I'm hoping to leverage some of the collective knowledge here regarding 2015 and later rear end axle differences. I currently have the opportunity to purchase a 2018 F-150 SuperCrew 3.5l Ecoboost 6.5' bed with...Our 1999-2004 Ford Dana 60 front axle identification guide will help you discover how to tell Dana 50 from 60 and Ford super duty front axle identification by axle tag Bill of Material (BOM) number using the ID codes on the axle tags. When the 1999 Ford F-250 and F-350 Super Duty® trucks were first introduced, all the Single Rear Wheel (SRW ...Sierra Gear & Axle is a premium line of light-duty differential parts. Products include ring and pinion sets, installation kits and axle shafts for GM, Ford, Chrysler, Jeep, and Toyota vehicles. Sierra Gear & Axle parts are designed and engineered to the highest quality specifications for use in street, off-road and performance environments.Look at the tag on your driver door. There is a category for Axle Code. Look at that code then Google it. You likely have 3.55 if you have a 4x4 or FX4 or max towing. Otherwise 3.31 would get my vote. The 10 speed trans defaults to the 3.31 unless other criteria is met as the 3.31 is a perfect match for the 10 speed.The Ford Sterling 10-1/2" Rear Full-Floating Axle was introduced in 1999 along with the new Super Duty F250 and F350. It shares some parts with the similar 10-1/4" Sterling Rear Axle which Ford used from 1985 to 1997 in the F250 and F350. The 10-1/2" Sterling is equipped with disc brakes (with the possible exception of some very early ...

Mobile platform since 2007 crossword clue

Axle Assembly. Ford Parts are the Only parts designed and built to the specific Standards of Ford Motor Company and are the Only parts recommended for use in your Ford or Lincoln vehicle. Right. Narrow axle. 4wd, f250,f350. To 10/01/2014. From 10/01/2014. w/ 4wd, w/o hd Suspension. Exc.Wide Track Front Suspension.

A 3.73 geared limited slip axle would be marked as : 3L73. An open differential would show 3(space)73. 102 denotes the ring gear size. 10.25 inches. ... decoder, differential, ford, h, identification, s, s406h, sterling, tag, truck. Back to Subforum. 1999 - 2003 7.3L Power Stroke Diesel. View Next Unread. Factory Ford remote starter wiring ...The 1957-1959 Ford styling revolution brought such cars as the Mystere show car and the Skyliner. See pictures and learn all about 1957-1959 Ford styling. Advertisement The 1957 st...Clutch, Transmission, Differential, Axle & Transfer Case - Nodular 9" Identification - I went through all 11 pages related to the nod 9, and couldn't come up with an answer, so... I've been looking for positive proof that I have a true nodular 9 . About 10 years ago, I bought the differential after wearing out some...Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear Axle ID. 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines. Sponsored by:Early Bronco Front Axle Identification: Dana 30 vs Dana 44. The first generation Ford Bronco came with either a Dana 30 or Dana 44 front axle. The Dana 30 was used from 1966 to mid-year 1971. At this point in 1971, Ford made the switch to the beefier Dana 44 front end and continued this through 1977, the last year of the early Bronco.axle identification. I think I answered my own question. I did a search over on the ford-diesel.com site and found a lot of info. I seems the tag on the axle has either a 229 or 248 and the 229 is a D50 and the 248 is a D60. I have the 248 or D60 axle. I …Dec 13, 2023 · Decoding Ford rear axle codes can be a bit complex, but by following a step-by-step process, it becomes much easier. Each letter and number in the rear axle code has a specific meaning, allowing you to extract valuable information about your axle. For example, the first two letters of the code indicate the axle’s size and capacity, while the ... The Dana 50 IFS was available as an option in pre-'87 F-250 HDs (4,600 pound HD front axle option) and was routinely fitted to SuperCab F-250 HDs. By 1987, the Dana 50IFS had replaced the Dana 44IFS in F-250HDs. A front limited slip shows up in Ford data books through at least 1985."1978-1979 Dana 60 Front Axles in Ford Trucks had a Ford Axle Code Tag with the Ford Production Part Number and Dana Bill of Material Number (BOM) stamped on a metal Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was shipped from the factory but, unfortunately, these tags are often missing on trucks that had prior ...Front axle identification. Was hoping some of y'all could help me identify the front axle in my 1971 F250 highboy. My warranty/info plate is missing off the door so can't find out that way. I am guessing it's a Dana 44hd due to 446cf being cast near the deferential cover, but was hoping someone could confirm or deny it.Ford Rear Axle Assembly Identification - Page 16: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V012-A: Ford Pass., Mercury 86-91: 2.73: 8.8: NL: 28-V012-B:

Rear Axle Identification - 1980 F100. Looks like a 2.75 to 1 ratio gear in it. I don't know about the rest. If it is smooth on the back of the housing, with no bolts, it's probably a 9 inch ford rear. Also being an f100, you might have a different lug pattern on your wheels than the more common 5 on 5.5. Reply Like.Sierra Gear & Axle is a premium line of light-duty differential parts. Products include ring and pinion sets, installation kits and axle shafts for GM, Ford, Chrysler, Jeep, and Toyota vehicles. Sierra Gear & Axle parts are designed and engineered to the highest quality specifications for use in street, off-road and performance environments.Ford Rear Axle Assembly Identification - Page 17: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V106A: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106B: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106C: Ford …When ordering Dana/Spicer Differential Parts provide bill of material number. This number is stamped on your right hand side axle tube. It's a number like 603XX-X, 604XX-X or 605XX-X. With this number you can tell exactly what components the factory used in the assembly of your differential. What is my Ford rear end ratio, do I have ...Instagram:https://instagram. astrazeneca pharmaceutical sales rep salary Differential Identification is the first and most important step in any differential repair or ratio change. Careful differential identification will help make sure you get the right parts for the job the first time. Dana Spicer and Ford Differentials can be identified most accurately by the tag number or axle tube stamp. Go to: Differential Tags la hacienda avon coupons Common axle ratio variants in Ford F150. Variants of Ford F150s have been built with varying axle ratios depending on the model year, engine size, or intended use. Commonly, we encounter axle ratios like 3.55, 3.73 or 4.10 in F150 models. This information can be found on the rear end tag or in the vehicle's service manual.Rear axle tag identification. I am trying to identify what kind of axle I just purchased. I was told it came out of a '66 Mustang Coupe with a 289. The axle tag reads: According to fordifcation.com they identified this axle coming out of a '65-'66 Mustang with a 2.80 axle ratio and a 7-3/4" ring gear. craigslist lincoln garage sales 1992-1997 Dana 60 Front Axles in Ford F-350 4x4 Trucks will typically have the Ford Build Code on a mylar decal affixed to the right axle tube. Also, the Dana Bill of Material Number (BOM) and Ford Build Code are stamped on a Build Tag (red arrow) attached to the differential by two of the differential cover bolts (yellow arrows) when the vehicle was …Originally Posted by BigBlue 94. My 99 e250 has a 24 axle code. I know it's an open 3.73 Dana 60. That follows ford code with a 2 digit numbered axle code being open and a letter /number digit code for limited slip. 1959 thru today: Two digit AXLE code. If the first digit is a letter: Limited Slip. greeting on deck crossword clue You are here: Home Tech Articles Front / Rear Differentials Ford Rear Axle Identification - Page 12. ‹ Back to Technical Index. Ford Rear Axle Assembly Identification - Page 12. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL or L. Axle Shaft Splines.Description: Rear Axle Paper ID Tag Year: 1968-1971 What's the right tag for your car? Check your build sheet for the right axle code for your car. If you don't have your build sheet, we have made up an axle tag application chart our supplier acquired from Ford, but it doesn't specify any difference between open and locking axles, except for the ones we have verified. hazlehurst salvage yard Ford Axle Identification by by Kenneth C at Bad Shoe Productions How To Video Series - Ford Transmissions & Rears Excerpts; "Photo 1 - The 9" rear ends have a removable "hog-head" center carrier and is about 10" from the bottom to the top stud. The 9" was introduced in 1957 and ran to mid 80's.28. D070-A. Tempo, Topaz 90-92. S102A. Ford F250 Pickup '97-99 (under 8500 GVW) Ford F150 Pickup '00 (7700 Series) 3.31. missouri employee salary Originally Posted by Jimmyspy. If it's actually from a level II, it's a 4.10 31 spline 8.8 with a Torsen L/S. From what I can tell, that's for a a 4.10 L/S 8.8. To confirm if 31 spline, measure the axle tubes. 31 spline axle will have larger axle tubes. The axle tubes are 3.25 inches. lynn item ma May 10, 2014 ... How to tell the difference between a Ford 9 inch and an 8 inch rear end/differential - Part 2 · Comments123.Look at the tag on your driver door. There is a category for Axle Code. Look at that code then Google it. You likely have 3.55 if you have a 4x4 or FX4 or max towing. Otherwise 3.31 would get my vote. The 10 speed trans defaults to the 3.31 unless other criteria is met as the 3.31 is a perfect match for the 10 speed. jetblue flight 1334 Aug 25, 2016 · And the axle tag says 4.10 and it's a limited slip rear. At the lower right corner of the tag it does have "LS". If the BOM says it's a LS it's probably a LS. And NumberDummy says if the axle code on your door decal starts with a letter, like yours does, then it's a LS. Reply Like. # 13. Ford Rear Axle Assembly Identification - Page 05: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WDY-A, A1: Comet '66-69 Fairlane '66-70 Falcon '66-70 Montego '70-74 Torino, '71-'74: 3.00: 8 in: NL: 28- george washington green one cent stamp The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates which Design Engineering Office is responsible for the component. There is a fair amount of detailed information contained within the part ...How To Read an Axle Label. Sprung and Torflex axle labels can be found on the side of the axle facing your rear bumper. The axle label provides critical manufacturing information, including the axle serial number, axle capacity, and axle build information. Locating your axle label will help ensure that you identify your axle correctly. h4ead premium processing BRONCO M220 REAR AXLE ASSEMBLY 4.70 RATIO W/ELECTRONIC LOCKING DIFFERENTIAL. M4000470B. $2,485.00. or redeem up to 497,000 Points. rubbermaid shed replacement parts Ford Rear Axle Assembly Identification - Page 14. NOTE: Axle tag location and appearance may vary by application. Code. Application. Ring Gear And Pinion. NL. or. L.I've had people tell me it's a Dana 60 and others say it's a Dana 70. I see 248 stamped into the axle, 05, and 2014828 with a B under it. Check the door jamb sticker and see what is listed under AXLE then compare to this list. AXLE CODES. 1968-Present E-Series Van/Cutaway/Chassis - Axle identification - Hi, I have a 2013 E-350, and I'm …Axle codes for Ford Explorer, Ranger and Bronco II. Axle identification Ford Explorer, Bronco II, Ranger.